| Command |
Description |
| ATA |
Answer incoming voice call |
| ATD<num>; |
Dial <num> in voice mode |
| ATDP |
(see ATD) |
| ATDT |
(see ATD) |
| ATE |
Turn Echo on / off |
| ATH |
Hang up. (in data or fax mode, change to voice
mode) |
| ATI[<num>] |
Request information
results for <num>:
0 = M9XX
1 = ffff
2 = ffff
3,4,6,7,8,9 = SAGEM FW4,1E
5 = 005
|
| ATO |
Switch from command state to online state
(in connection) |
| ATQ |
Set Quiet Mode |
| ATS<reg>=<val>
|
Write <val> to register <reg>:
ATS<reg>? reads content of register.
Allowed registers:
3 = command line termination character (#13 = CR)
4 = response formatting character (#10 = LF)
5 = command line editing character (#8 = BS)
(Values in parentheses are default values) |
| ATV |
Set verbose return codes |
| ATZ0 |
Reset to Profile 0 |
| ATZ |
Reset |
| AT&D<val> |
Set DTR Options:
0 = ignore DTR,
1 = DTR on-to-off transistion enters command mode,
2 = hang up and enter command mode on DTR drop,
3 = reset modem and hang up on DTR drop |
| AT&F |
Load default Settings |
| AT&K<val> |
Set Local Flow Control:
0 = none,
3 = RTS/CTS,
4 = XON/XOFF,
5 = Transparent XON/XOFF,
6 = CTS/RTS and XON/XOFF |
| AT&V |
Display Profile Settings |
| AT&W |
Save Profile Settings |
| |
|
| AT+CAOC[=<mode>]
|
"Advice of Charge" Reporting
AT+CAOC returns "+CAnnnnnn" with nnnnnn being the current call meter
in 3 hex bytes
AT+CAOC? returns current settings
AT+CAOC=? returns allowed values for <mode>:
0 = query CCM value (same as AT+CAOC)
1 = disable reporting of CCM over cable
2 = enable reporting of CCM values over cable |
| AT+CBST=<speed>,<name>,<ce>
|
Select Bearer Service Type
AT+CBST? returns current settings
AT+CBST=? returns a list of possible values:
values for <speed>:
0 = automatic selection
4 = 2400 bps V.22bis
6 = 4800 bps V.32
7 = 9600 bps V.32
68 = 2400 bps V.110
70 = 4800 bps V.110
71 = 9600 bps V.110
values for <name>:
0 = data circuit asynchronous
values for <ce>:
0 = transparent
1 = non-transparent |
| AT+CDIS |
Display Control (always returns OK?)
|
| AT+CEER |
Extended Error Reports |
| AT+CGMI |
Request Manufacturer Identification.
Returns "+CGMI: SAGEM". |
| AT+CGMM |
Request Model identification.
Returns "+CGMM: M9XX". |
| AT+CGMR |
Request Revision identification.
Returns "+CGMR: SAGEM FW4,1E". |
| AT+CGSN |
Request Product Serial Num identification
(IMEI) |
| AT+CHUP |
Hang up, terminate the call without changing
to voice mode from alternating data/voice mode. (see also ATH)
|
| AT+CIMI |
Request International Mobile Subscriber identity
(IMSI) |
| AT+CIND=<battchg>,<signal>,<service>,<call>
|
Indicator Control
(AT+CIND? returns current values)
(AT+CIND=? returns possible values)
values for <battchg>
0 = empty battery ... 5 = full battery
values for <signal>
0 = no signal ... 5 = strong signal
values for <service>
0 = no service available
1 = service available
values for <call>
0 = no call in progress
1 = call in progress |
| AT+CKPD="<keys>"[,<time>[,<pause>]]
|
Keypad Control
(AT+CKPD=? returns list of allowed keys)
allowed values for <keys>: any string formed from the following
characters:
0 .. 9,#,* : buttons 0 .. 9,#,*
C = Clear Display
D = Volume down
E = End connection
M = Menu
O = Power Off
S = Start connection
U = Volume up
V = Down arrow
X = Auxiliary (programmable button ".")
Y = delete last character
Z = Ok
^ = Up arrow
<time> and <pause>:
time to hold button/pause between buttons. Allowed values: 0 .. 255
ms (->0 .. 25.5 seconds) |
| AT+CLAC |
List all available AT commands |
| AT+CLCC |
List current calls |
| AT+CLIP=<n> |
Calling Line Identificaion Presentation
(AT+CLIP? returns current settings as "+CLIP: <n>,<m>")
(AT+CLIP=? returns possible values for <n>)
possible values for <n>
0 = disable
1 = enable
possible values for <m>
0 = CLIP not available in network
1 = CLIP available in network
2 = CLIP status unknown |
| AT+CLIR=<n> |
Calling Line Identification Restriction
(AT+CLIR? returns current settings as "+CLIR: <n>,<m>")
(AT+CLIR=? returns possible values for <n>)
possible values for <n>
1 = CLIR enabled
2 = CLIR disabled
possible values for <m>
0 = CLIR not available in network
1 = CLIR available in permanent mode
2 = CLIR status unknown
3 = CLIR temporary mode presentation restricted
4 = CLIR temporary mode presentation allowed |
| AT+CMEC=<keyp>,<disp>,<ind>
|
Mobile Equipment Control Mode
(AT+CMEC? returns current settings)
(AT+CMEC=? returns a list of possible settings)
values for <keyp>:
2 = Keypad and datacable operation
values for <disp>:
0 = Only phone can write to display
values for <ind>:
0 = only phone can set indicator status |
| AT+CMEE=<mode>
|
Mobile Equipment Error Reporting
(AT+CMEE? returns current setting)
AT+CMEE=? returns allowed values for <mode>:
0 = Errors are reported as "ERROR"
1 = Errors are reported as "+CME ERROR: <err>".
See error result codes for more information.
|
| AT+CMER=<mode>,<keyp>,<disp>,<ind>,<bfr>
|
Mobile Equipment Event Reporting
(AT+CMER? returns current settings)
(AT+CMER=? returns possible settings)
possible values for <mode>
0 = store event result codes in phone
possible values for <keyp>
0 = no keypad event reporting over cable
possible values for <disp>
0 = no display event reporting over cable
possible values for <ind>
0 = no indicator event reporting over cable
possible values for <bfr>
0 = clear event buffer when entering <mode> 1-3
|
| AT+CNUM |
Subscriber Number. Returns phonebook entry
for own number. |
| AT+COPN |
Read Operator Names |
| AT+CPAS |
Query Phone Activity Status
(AT+CPAS=? returns a list of possible values)
The current status is reported as "+CPAS: <pas>"
values for <pas>:
0 = phone ready
4 = call in progress |
| AT+CPBF |
Find Phonebook entries |
| AT+CPBR |
Read Phonebook entries |
| AT+CPBS |
Select Phonebook memory Storage |
| AT+CPBW |
Write Phonebook entry |
| AT+CPIN="<pin>"[,"<new_pin>"]
|
Enter Pin code
AT+CPIN? reports current state:
+CPIN: READY = no pin required
+CPIN: SIM PIN,PIN2,PUK,PUK2,... = required pin
If a new pin is to be set, <pin> should be the PUK, and <new_pin>
should be the new pin. |
| AT+CPOF |
Turn Power off.
|
| AT+CPOL |
Preferred Operators List |
| AT+CPWD="<type>","<old>","<new>"
|
Change Password
AT+CPWD=? returns allowed values for <type> and the maximum
length:
P2 = SIM pin 2, max. 8 digits
SC = SIM password, max. 8 digits |
| AT+CREG=<n> |
Network Registration Reporting
(AT+CREG? returns current settings as +CREG: <n>,<stat>[,"<lac>","<cid>"])
(AT+CREG=? returns a list of possible values for <n>)
possible values for <n>:
0 = disable network registration reporting
1 = enable network registration reporting
2 = enable network registration and location information reporting
possible return values for <stat>:
0 = not registered, not searching for network
1 = registered at home network
2 = not registered, searching network
3 = registration denied
4 = registration status unknown
5 = registered, but not in home network (roaming)
If location information reporting is enabled, the output will contain
two additional fields:
<lac> = location area code (4 hex digits)
<cid> = cell id (4 hex digits) |
| AT+CRLP<iws>,<mws>,<T1>,<N2>,<ver>,<T4>
|
Radio Link Protocol Parameters for Data Calls
AT+CRLP? returns current settings
AT+CRLP=? returns a list of allowed values.
<iws>: IWF to MS window size
allowed: 0 .. 61, default is 61
<mws>: MS to IWF window size
allowed: 0 .. 61, default is 25
<T1>: Acknowledgement timer
allowed: 0 .. 255 [ms], default is 48
<N2>: Retransmission attempts
allowed: 0.. 255, default value is 6
<ver>: RLP version, ver = 0
<T4>: Resequencing Period
allowed: 0 .. 255 [ms], default is 7
Note: As this command influences the data transmission protocol, it
would be a good idea to leave it alone unless you know what you are
doing. |
| AT+CR=<mode> |
Service Reporting Control
(AT+CR? returns current <mode>)
(AT+CR=? returns a list of possible modes)
Possible values for <mode>:
0 = disable mode reporting
1 = enable mode reporting
when reporting is enabled, the phone will report the service type
with "+CR: <serv>" before reporting "CONNECT".
possible values for <serv>:
ASYNC : asynchronous transparent
SYNC : synchronous transparent
REL ASYNC : asynchronous non-transparent
REL SYNC : synchronous non-transparent |
| AT+CSCS=<chset>
|
Select TE Character Set
(AT+CSCS? returns current setting)
(AT+CSCS=? returns a list of possible settings)
values for <chset>:
PCCP437 = PC character set, Code page 437 |
| AT+IPR=<speed>
|
Set TE Data Rate
AT+IPR? queries current setting
AT+IPR=? returns a list of allowed values.
Allowed values for <speed>:
2400 = 2400 bps
4800 = 4800 bps
9600 = 9600 bps
19200 = 19200 bps
|
| |
|
| AT+CNMI=<mode>,<mt>,<bm>,<ds>,<bfr>
|
New Message Indication to TE
(AT+CNMI? returns current settings)
value for <mode>: 1 = no indication if serial port in use
value for <mt>: 1 = report new sms memory location
value for <bm>: 0 = no cb message indication
value for <ds>: 0 = no sms status reporting
value for <bfr>: 0 = flush buffer when new <mode>
|
| AT+CMGD |
Delete Message |
| AT+CMGF |
Message Format |
| AT+CMGL |
List Messages |
| AT+CMGR |
Read Message |
| AT+CMGS |
Send Message |
| AT+CMGW |
Write Message to Memory |
| AT+CMSS |
Send Message from Storage |
| AT+CPMS |
Preferred Message Storage |
| AT+CSCA |
Service Center Address |
| AT+CSMP |
Set Text Mode Parameter |
| |
|
| AT+FCLASS=<val>
|
Select Mode: (AT+FCLASS? returns current setting)
0 = Data,
1 = Fax Class 1,
8 = Voice |
| AT+FAE=<val> |
Set auto answer for Data/Fax: (AT+FAE? returns
current setting)
0 = Data,
1 = Fax class 1 |
| AT+FRS=<val> |
Check for Silence: (AT+FRS? returns current
setting)
report "OK" after <val>*10ms of silence |
| AT+FRM=<val> |
Receive Data with defined Data Rate: (AT+FRM=?
returns current setting)
24 = 2400 bps
48 = 4800 bps
72 = 7200 bps
96 = 9600 bps |
| AT+FTM=<val> |
Transmit Data with defined Data Rate: (AT+FTM=?
returns current setting)
(see AT+FRM for values) |
| AT+FRH=<val> |
Receive Data with HDLC: (AT+FRH=? returns
current setting)
3 = V.21 channel 2 300 bps |
| AT+FTH=<val> |
Transmit Data with HDLC: (AT+FTH=? returns
current setting)
(see AT+FRH for values) |
| AT+FTS=<val> |
Stop transmission: (AT+FTS? returns current
setting)
Terminate transmission and wait <val>*10ms before "OK"
|
| |
|
| AT\N0 |
Disable MNP Error Correction |
| AT\N4 |
Set V.42 Error Correction |
| AT\N6 |
Set V.42 Error Correction, Fallback to MNP
|
| AT\V |
Enable verbose MNP Result Codes |
| Error code
| Meaning |
| 0 |
phone failure |
| 1 |
no connection to phone |
| 2 |
phone-adaptor link reserved |
| 3 |
operation not allowed |
| 4 |
operation not supported |
| 5 |
PH-SIM PIN required |
| 6 |
PH-FSIM PIN required |
| 7 |
PH-FSIM PUK required |
| 10 |
SIM not inserted |
| 11 |
SIM PIN required |
| 12 |
SIM PUK required |
| 13 |
SIM failure |
| 14 |
SIM busy |
| 15 |
SIM wrong |
| 16 |
incorrect password |
| 17 |
SIM PIN2 required |
| 18 |
SIM PUK2 required |
| 20 |
memory full |
| 21 |
invalid index |
| 22 |
not found |
| 23 |
memory failure |
| 24 |
text string too long |
| 25 |
invalid characters in text string
|
| 26 |
dial string too long |
| 27 |
invalid characters in dial string
|
| 30 |
no network service |
| 31 |
network timeout |
| 32 |
network not allowed - emergency calls only
|
| 40 |
network personalisation PIN required
|
| 41 |
network personalisation PUK required
|
| 42 |
network subset personalisation PIN required
|
| 43 |
network subset personalisation PUK required
|
| 44 |
service provider personalisation PIN required
|
| 45 |
service provider personalisation PUK required
|
| 46 |
corporate personalisation PIN required
|
| 47 |
corporate personalisation PUK required
|
| 100 |
unknown |